How to Make a Phone Charm: Materials, Styles & DIY Tips

How to Make a Phone Charm

A phone charm is a short strap of cords and beads that loops through your phone case. Making one at home is easy. You tie a loop, thread beads onto both halves, and knot the ends together. The whole project fits in one sitting and needs only a few basic supplies.

Three choices shape the final result: the cord, the style, and the finish. This guide covers each one, then shows you how to build, attach, and fix your charm.

Pick the Right Materials

Start with the cord, because it decides how strong your charm will be.

Tug a short piece. If it stretches, it suits decoration only. If it barely stretches, it can carry the weight of a phone.

Elastic stretches while waxed polyester and nylon hold firm. Braided cord is thick and strong and looks handmade, but it needs bigger bead holes.

Keep the cord about 1 mm thick. That size slides through most beads and still fits most case openings.

Then choose your beads:

● Acrylic beads stay light and come in every color

● Wooden beads feel warm and natural

● Glass beads shine but add weight

● Tiny seed beads make good spacers between larger pieces

Stick to two or three bead sizes at most. Too many sizes make the strap look busy.

Gather a few extras too:

● A lobster clasp or jump ring for hanging a charm

● A crimp bead or knot cover for a clean finish

● Clear nail polish or glue to seal knots

● A lighter (only if you want to melt waxed cord ends)

Test one bead before you buy a whole pack. The cord should slide through the hole without any force. If you plan to pass a strand back through, the hole must fit two passes.

Phone Charm Styles to Try

Pick a style based on how you hold your phone and the color of your phone case.

Color Block Pop

Group beads by color in bold stretches. Use three or four shades that sit far apart on the color wheel. This style works best on plain or clear cases, where the charm gets all the attention.

Tonal Minimal

Stay inside one color family. Mix matte and glossy beads of the same shade for depth. The look is calm and pairs well with neutral cases.

Pearl Strand

String small pearl or glass beads on a thin cord. Keep the strap short so it hangs like a necklace. Light beads stop a delicate charm from tugging on the case.

Charm Drop

Use a short run of beads, then end with one acrylic or metal charm. Attach it with a jump ring or lobster clasp. The charm becomes the star item, so pick one with a clear shape.

Name Charm

Use letter beads to spell a name or short word in the middle of the strap. Add plain beads on each side to frame it. This version makes a thoughtful gift, since it takes minutes to personalize.

Wrist Grip

Make the strap long enough to slip over your hand. Use waxed or nylon cord and a double knot for this. This style suits anyone who holds the phone while walking.

Match the weight to your case, because thin cases flex and wear under heavy beads.

How to Make a Beaded Phone Charm

How to Make a Beaded Phone Charm

Every style above uses the same build. You fold one cord in half and bead both sides.

Measure and Cut

Decide how long each half of the finished strap should be. Then use this simple rule: double that length, and add four inches. The extra four inches is for covering the loop and the knots.

For example, a five-inch half requires a 14-inch cord. Most charms look right between five and seven inches per half. To size a wrist strap, wrap a piece of cord around your hand and mark it before you cut.

Tie the Loop

Fold the cord in half. Tie a simple knot one to two inches below the fold. That gap becomes the loop that holds the charm on your case.

Make the loop larger if you're using chunky beads. Then pull the knot snug and check that no bead can slip over it. If possible, double the knot or start with a larger bead.

Thread the Beads

String one test inch first. Check the colors and the fit. Then bead each half, one bead at a time, and keep both sides the same length. Dab clear polish on any fraying tip and let it dry before you continue.

Close and Secure

For the final step, hold both ends together and tie a double knot. Leave a finger's width of gap so the beads can move. Dab the knot with clear polish or glue, and let it dry fully. Then give the strap a firm pull. A weak knot shows itself right away.

Skip the lighter if you have never used one or are new to crafts. Polish or glue works just as well. Finally, trim the tails close to the knot.

How to Attach a Phone Charm to Your Case

Start by taking the phone out of the case. Push the loop through the lanyard hole or through a button cutout if your case has no hole. Then thread the charm through the loop and pull it snug.

The lanyard hole is the best choice, since makers build it for that pull. Otherwise, choose the opening with the thickest edge. To test the hold, grip the strap and lift the case a few inches above a bed or sofa.

If your case has no holes or strong openings, try a tether tab. This thin patch slips through the charging port of a full-coverage case and gives you a loop to tie onto.

That's how you make a phone charm and attach it to your case. If you enjoyed beading and want to explore more projects like this, try beaded keychains next. 

Tips to Make Your Charm Last

Beads slip off: Double the knot, or place a larger bead beside it.

Cord frays: Trim it clean and seal the tip with clear polish.

Strap sags: Swap elastic cord for waxed or nylon cord.

Charm feels heavy: Cut the bead count or switch to light acrylic beads.

Knot loosens: Add another drop of glue and let it set overnight.

A good cord choice solves most of these problems, so make sure to pick the right one.

Get Your Own Artwork on a Phone Charm With Vograce

Get Your Own Artwork on a Phone Charm With Vograce

Hand beading is meditative and beginner-friendly, and it gives you control over color, but it cannot print your own artwork.

That is where Vograce comes in. Our custom beaded phone charms carry double-sided printed acrylic, with the same design on both sides or a different one on each. Each strap holds five such charms, and you can also pick from various colored straps. The best part is turning your artwork into cute acrylic pieces and using them to make your phone charms.

You simply upload your art, and we handle the printing and everything else. You can order a single piece to test your design or place larger orders and save money per piece, which is perfect if you plan to sell them.

On This Page